Pick N Pluck Foam Peli 1022 (for 1020 Micro Case)
Give your Peli™ 1020 Micro Case a tailored interior with the 1022 Pick N Pluck™ foam insert. Instead of settling for a loose-fitting cavity or reaching for a knife and glue, you shape the exact cradle your gear needs by hand — cube by cube, no tools required.
How Pick N Pluck Foam Works
The insert is pre-scored into a tight grid of small foam cubes. Trace the outline of whatever you're packing directly onto the foam, then pluck out the cubes inside that outline with your fingers. Work slowly and test-fit as you go — it's far easier to remove another cube than to put one back. Keep at least a 2.5 cm (1 inch) margin of foam around every item; that surrounding cushion is what actually absorbs shock in a drop or knock, so resist the temptation to carve right up to the case wall.
Made to Fit the 1020, Precisely
This insert is cut to the exact footprint of the Peli 1020 Micro Case, with a foam piece measuring 13.2 × 8.9 × 2.3 cm. Use it as a direct swap for a base foam that's been over-plucked, stained, or worn out, or keep a spare on hand so one case can serve double duty — one cavity carved for today's gear, a fresh block ready for tomorrow's.
Real-World Uses
The 1020 is one of the smallest cases in the Peli micro range, so this foam tends to end up cushioning things that are easy to lose or crack: a phone and its charging cable on a building site, a compact camera and spare battery on a hike, a portable hard drive travelling between office and home, a handheld GPS unit on a boat, or a handful of small tools and connectors in a service van. The dense grey polyurethane holds its shape through repeated packing and unpacking, so the cavity you carve today should still be doing its job months later.
Why It's Worth Doing Properly
A loose item rattling around inside a hard case usually causes more damage than dropping the case itself — vibration and impact get concentrated on whatever corner happens to hit first. A well-fitted Pick N Pluck cavity spreads that load evenly across the foam instead, which is the same logic Peli's own hard cases are built around: a tough polymer shell paired with foam shaped to the contents, not the other way round.
Quick Tips Before You Start
- Lay your item on the foam and trace it lightly before plucking — cubes are easy to remove but impossible to put back.
- Leave the 2.5 cm foam margin on all sides, including underneath the item.
- Packing more than one item? Group them close together rather than spreading separate cavities across the block — it keeps the surrounding foam wall intact and rigid.
- Brush or vacuum out loose foam crumbs before closing the case; a few stray cubes are normal and won't affect the fit.
Specifications
Foam piece exterior: 13.2 × 8.9 × 2.3 cm. Material: pre-diced cube (Pick N Pluck) polyurethane foam, grey. Compatible with: Peli 1020 Micro Case, as a replacement or spare base foam.
Give your Peli™ 1020 Micro Case a tailored interior with the 1022 Pick N Pluck™ foam insert. Instead of settling for a loose-fitting cavity or reaching for a knife and glue, you shape the exact cradle your gear needs by hand — cube by cube, no tools required.
How Pick N Pluck Foam Works
The insert is pre-scored into a tight grid of small foam cubes. Trace the outline of whatever you're packing directly onto the foam, then pluck out the cubes inside that outline with your fingers. Work slowly and test-fit as you go — it's far easier to remove another cube than to put one back. Keep at least a 2.5 cm (1 inch) margin of foam around every item; that surrounding cushion is what actually absorbs shock in a drop or knock, so resist the temptation to carve right up to the case wall.
Made to Fit the 1020, Precisely
This insert is cut to the exact footprint of the Peli 1020 Micro Case, with a foam piece measuring 13.2 × 8.9 × 2.3 cm. Use it as a direct swap for a base foam that's been over-plucked, stained, or worn out, or keep a spare on hand so one case can serve double duty — one cavity carved for today's gear, a fresh block ready for tomorrow's.
Real-World Uses
The 1020 is one of the smallest cases in the Peli micro range, so this foam tends to end up cushioning things that are easy to lose or crack: a phone and its charging cable on a building site, a compact camera and spare battery on a hike, a portable hard drive travelling between office and home, a handheld GPS unit on a boat, or a handful of small tools and connectors in a service van. The dense grey polyurethane holds its shape through repeated packing and unpacking, so the cavity you carve today should still be doing its job months later.
Why It's Worth Doing Properly
A loose item rattling around inside a hard case usually causes more damage than dropping the case itself — vibration and impact get concentrated on whatever corner happens to hit first. A well-fitted Pick N Pluck cavity spreads that load evenly across the foam instead, which is the same logic Peli's own hard cases are built around: a tough polymer shell paired with foam shaped to the contents, not the other way round.
Quick Tips Before You Start
- Lay your item on the foam and trace it lightly before plucking — cubes are easy to remove but impossible to put back.
- Leave the 2.5 cm foam margin on all sides, including underneath the item.
- Packing more than one item? Group them close together rather than spreading separate cavities across the block — it keeps the surrounding foam wall intact and rigid.
- Brush or vacuum out loose foam crumbs before closing the case; a few stray cubes are normal and won't affect the fit.
Specifications
Foam piece exterior: 13.2 × 8.9 × 2.3 cm. Material: pre-diced cube (Pick N Pluck) polyurethane foam, grey. Compatible with: Peli 1020 Micro Case, as a replacement or spare base foam.
Original: $10.84
-65%$10.84
$3.79Description
Give your Peli™ 1020 Micro Case a tailored interior with the 1022 Pick N Pluck™ foam insert. Instead of settling for a loose-fitting cavity or reaching for a knife and glue, you shape the exact cradle your gear needs by hand — cube by cube, no tools required.
How Pick N Pluck Foam Works
The insert is pre-scored into a tight grid of small foam cubes. Trace the outline of whatever you're packing directly onto the foam, then pluck out the cubes inside that outline with your fingers. Work slowly and test-fit as you go — it's far easier to remove another cube than to put one back. Keep at least a 2.5 cm (1 inch) margin of foam around every item; that surrounding cushion is what actually absorbs shock in a drop or knock, so resist the temptation to carve right up to the case wall.
Made to Fit the 1020, Precisely
This insert is cut to the exact footprint of the Peli 1020 Micro Case, with a foam piece measuring 13.2 × 8.9 × 2.3 cm. Use it as a direct swap for a base foam that's been over-plucked, stained, or worn out, or keep a spare on hand so one case can serve double duty — one cavity carved for today's gear, a fresh block ready for tomorrow's.
Real-World Uses
The 1020 is one of the smallest cases in the Peli micro range, so this foam tends to end up cushioning things that are easy to lose or crack: a phone and its charging cable on a building site, a compact camera and spare battery on a hike, a portable hard drive travelling between office and home, a handheld GPS unit on a boat, or a handful of small tools and connectors in a service van. The dense grey polyurethane holds its shape through repeated packing and unpacking, so the cavity you carve today should still be doing its job months later.
Why It's Worth Doing Properly
A loose item rattling around inside a hard case usually causes more damage than dropping the case itself — vibration and impact get concentrated on whatever corner happens to hit first. A well-fitted Pick N Pluck cavity spreads that load evenly across the foam instead, which is the same logic Peli's own hard cases are built around: a tough polymer shell paired with foam shaped to the contents, not the other way round.
Quick Tips Before You Start
- Lay your item on the foam and trace it lightly before plucking — cubes are easy to remove but impossible to put back.
- Leave the 2.5 cm foam margin on all sides, including underneath the item.
- Packing more than one item? Group them close together rather than spreading separate cavities across the block — it keeps the surrounding foam wall intact and rigid.
- Brush or vacuum out loose foam crumbs before closing the case; a few stray cubes are normal and won't affect the fit.
Specifications
Foam piece exterior: 13.2 × 8.9 × 2.3 cm. Material: pre-diced cube (Pick N Pluck) polyurethane foam, grey. Compatible with: Peli 1020 Micro Case, as a replacement or spare base foam.
